제품명 or 모델명검색

 제품소개
 FLUKE
 BAUR
 BRUKER
 Chroma
 Dewesoft
 YOKOGAWA
 GRAPHTEC
 ISA
 IWATSU
 Hioki
 KIKUSUI
 NOISEKEN
 NIT
 Noise & Vibration
 유량계
 압력센서
 온도센서
 TECHIMP
 TEMPSEN
 Nf
 Signal Generators
 LCR Meters
 Impedance/Gain-Phase Analyzer
 AC Voltmeter / Noise Meter
 Lock-in Amplifiers / Preamplifiers
 Filters
 Measurement System
 Frequency Response Analyzers
 AC Power Sources
 Power Amplifiers
 Electronic Loads
 Power Test Instruments
 ATCP


 

 글쓴이 : 피앤에스
조회 : 553  

 

  [Lock-in Amplifiers / Preamplifiers] Preamplifier

  모델명 :


Programmable Current Amplifier
CA5350

Our Experience and Know-How Made Sure the Amplifier Was Packed with the Advantages of DSP.

The CA5350 programmable current amplifier is a variable gain type, current-input, voltage-output amplifier. Gain can be set from 104 V/A to a maximum of 1011 V/A. In addition, the included current suppression function enables the canceling of the dark current that cannot be avoided with photoelectric conversion elements such as photodiodes.
BNC connectors are used for input and output, so special cables or an external power supply are not required. The various settings, including gain, are easy to perform using the dial and keys on the front panel, and the set values are displayed on the screen.
Since the GPIB and USB interfaces make remote control also possible, gain and other settings can be performed from a personal computer, making it easy to configure an automatic measurement system.
With its performance, functions and operability, this programmable current amplifier supports the current amplification of signals from a variety of current output sensors.

LI 5640/LI 5630


Low Noise Preamplifier
SA series
SA series are preamplifiers for submicro-signal detection, which have been developed to assure noise reduction never before accomplished.
7 types of SA series amplifiers, which vary by a frequency range, input form, and input impedance, are available.

SA-200F3
Low Noise Amplifier
SA-220F5
Low Noise FET Amplifier
SA-230F5
Low Noise Amplifier
SA-200F3
SA-220F5
SA-230F5

SA-400F3
Low Noise Differential Amplifier
SA-420F5
Low Noise Differential FET Amplifier
SA-421F5
Low Noise Differential FET Amplifier
SA-430F5
Low Noise Differential Amplifier
SA-400F3
SA-420F5
SA-421F5
SA-430F5
+



Low Noise DC Power Supply
LP5393/LP5394

Our Experience and Know-How Made Sure the Amplifier Was Packed with the Advantages of DSP.

Utilizing our proprietary circuit design technology, the LP series of ultra-low noise DC power supplies provides output voltage with extremely low levels of noise. The main unit is shielded and shielded connectors and cables are used to prevent the emission of internal noise as well as prevent external 
noise from affecting the signal. The combination of all these technologies results in a DC power 
supply that produces output with a superior level of low noise. 
The LP series is suitable for high-precision measurement applications such as sensor preamp 
power supplies and DC bias power supplies used in advanced device research, analysis devices, 
and medical equipment.

LI 5640/LI 5630


Differential Amplifier
5307
5307
The 5307 is a general-purpose low-noise differential amplifier featuring a bandwidth of DC to 10MHz, a maximum gain of 1000 and a noise level of 4nV/√Hz.

Wide bandwidth : DC to 10MHz

High gain : 10 to 1000

Differential input (single-ended configuration also selectable)

High CMRR : 120dB or higher

High common mode voltage : ± 10V

Low noise : 4nV/√Hz.typ. (1kHz)

Current Input Preamplifier
LI-76
LI-76
LI-76
The LI-76 is a current-input preamplifier which covers signals from photo-multipliers, PIN diodes and similar sources into voltage signals.



Low Noise DC Power Supply
LP5393/LP5394

Our Experience and Know-How Made Sure the Amplifier Was Packed with the Advantages of DSP.

Utilizing our proprietary circuit design technology, the LP series of ultra-low noise DC power supplies provides output voltage with extremely low levels of noise. The main unit is shielded and shielded connectors and cables are used to prevent the emission of internal noise as well as prevent external 
noise from affecting the signal. The combination of all these technologies results in a DC power 
supply that produces output with a superior level of low noise. 
The LP series is suitable for high-precision measurement applications such as sensor preamp 
power supplies and DC bias power supplies used in advanced device research, analysis devices, 
and medical equipment.

LI 5640/LI 5630









 
 

Total 33
[Signal Generators]
Digital Function… 
DF1906
[Signal Generators]
Multifunction Sy… 
[Signal Generators]
Multifunction Ge… 
WF1973 / WF1974
[Signal Generators]
Multifunction Ge… 
WF1967/WF1968
[Signal Generators]
Clock Synthesize 
CK1615 / CK1620
[LCR Meters]
LCR Meter 
ZM2371/ZM2372/ZM2376
[Impedance/Gain-Phase Analyzer]
Impedance/Gain-P… 
ZGA5920
[AC Voltmeter / Noise Meter]
AC Voltmeter/Noi… 
[Lock-in Amplifiers / Preamplifiers]
Light Chopper 
5584A
[Lock-in Amplifiers / Preamplifiers]
Isolation Amplif… 
5325
[Lock-in Amplifiers / Preamplifiers]
Preamplifier 
[Lock-in Amplifiers / Preamplifiers]
Lock-in Amplifie… 
[Filters]
Filter 
[Measurement System]
Measurement Syst… 
MS-500 series
[Frequency Response Analyzers]
Frequency Respon… 
FRA5087/FRA5097/FRA5022
[AC Power Sources]
Programmable AC … 
DP series
 
 
 1  2  3  

관리자로그인로그아웃